Home Bosch Rexroth Indramat KDA Spindle Drives KDA 3.3-150-3-A00-W1

KDA 3.3-150-3-A00-W1

Name: KDA 3.3-150-3-A00-W1
Brand: Bosch Rexroth Indramat
Price: 308 USD
Availability: InStock
Rating: 4.6 (13 reviews)

Rated 4.6 (13 total ratings)

MPN: R911257443

No Tariffs On US Orders

Straightforward Pricing: No Rush Fees, No Credit Card Fees

In-Stock, Ships 3-5 Days

Preparing your secure checkout page...

KDA 3.3-150-3-A00-W1 is a spindle drive. It works with 2AD and 1MB motors. Its rated output is 150 Amps.

Quote Request Form:

Phone

Part Number

Message (Optional)

Website

Include Repair Options

Have a part to sell?

Wake Industrial Warranty

To contact sales for pricing and lead time:

Phone: 1-888-551-3082

International: 1-919-443-0207

Email: sales@wakeindustrial.com

Payment Methods

Shipping Methods

Our Credentials

Product Description:

KDA 3.3-150-3-A00-W1 is a main spindle drive. Bosch KDA drives are used for control of 2AD asynchronous motors and 1MB frameless spindle motors. A microcomputer carries out drive control, monitoring and diagnostics. This is aided by an accurate measurement of motor rotor position over the entire speed range. In addition to speed control, KDA drives provide a high degree of internal position control. Adaptation of motors and operation modes is done through parametrization, which is performed by an integrated input and display unit. The KDA 3.3-150-3-A00-W1 drive is designed for forced air cooling. It is equipped with a blower that requires 220 Volts AC external supply. DC bus voltage of the drive is 300 Volts DC. Its rated current output is 150 Amps and the continuous current output is 90 Amps.

The control electronics consume 1.6 Amps at 24 Volts DC and 160 milliamps at 15 Volts DC measuring voltage. Weight of the spindle drive unit is 17.4 kilograms. The blower unit weighs 4.2 kilograms. Weight of the mechanical mounting kit is 1.7 kilograms. The ambient temperature required for rated output is 5 to 45 degrees Celsius. The permitted maximum temperature with reduced nominal data is 55 degrees Celsius. Bosch recommends -30 to 85 degrees Celsius ambient temperature for storage and transport. The specified installation elevation without reduction of nominal data is 0 to 1000 meters. Protection category of the drive housing is IP10. The unit is designed for vertical mounting inside a suitable cabinet. Only trained personnel with relevant qualifications should handle and install the KDA 3.3-150-3-A00-W1 spindle drive. Failure to implement manufacturer instructions can lead to equipment damage and injury to personnel.

Click here to learn more about the uses for the KDA 3.3-150-3-A00-W1 and other Indramat Spindle Drives.

Specs
Revisions
Common Troubleshooting Steps
Product Comparison
Similar Ordering Codes
Common Error Codes

Additional encoder input
No

Additional interface
No

Blower supply
220 Volts AC

Cooling
Blower

Current rating
150 Amps

DC bus voltage
300 Volts DC

Manufacturer
Bosch Rexroth

Mounting
Vertical

Product type
Main spindle drive

Speed command
Analog

KDA 3.3 150 3 A00 W1
KDA 3.31503A00W1
KDA- 3.3-150-3-A00-W1

Typical fault code / symptom	What it usually means	Quick corrective action
F205 — switching to un-initialised operating mode	Required mode not stored in parameters S-0-0032…35	Enter the correct spindle-mode parameters, save, then issue Reset Class 1 Diagnostics or power-cycle drive.
F218 — heat-sink over-temperature	Internal heat-sink > allowed limit	Clean or replace heat-sink blower, improve cabinet airflow, wait < 45 °C, then reset.
F219 — motor over-temperature	2AD/1MB motor thermistor tripped (≈ 155 °C)	Reduce load, check external motor fan, allow full cool-down before re-enable.
F220 — bleeder-resistor over-temperature	Internal regen resistor overheated	Add/ex-size external brake resistor or lengthen decel ramps; clear when cool.
F226 — DC-bus under-voltage	Bus < ~270 V while drive enabled	Check KDV power supply and bus cabling for brown-outs; reset after mains OK.
F228 — excess following-error	Spindle cannot track speed demand	Reduce accel/dec ramp, inspect mechanics for drag, retune velocity loop.
F229 — encoder-quadrant error	Resolver/encoder plausibility fault	Inspect feedback cable & shielding, replace encoder or interface if repeat.
F230 — encoder-frequency too high	Spindle speed > encoder interface limit	Limit top speed or fit lower-PPR encoder; clear and restart.
F233 / 34 — +24 V control-supply error / E-Stop active	External 24 V lost (often via E-Stop chain)	Restore 24 V, clear E-Stop, then perform Class 1 Reset.
Display dark & blower runs continuously	Drive in thermal or HW self-protection	Measure DC-bus (≈ 300 V) and 24 V, check blower supply (220 VAC), replace drive if self-test fails.

Model	Series / design	Rated current (A)	DC-bus voltage (V)	Cooling	Notable feature
KDA 3.3-150-3-A00-W1	3.3	150	300	Forced (heat-sink blower, 220 VAC)	Highest-current 3.3 design
KDA 3.2-150-3-A00-W1	3.2	150	300	Forced	Earlier firmware line 3.2, otherwise drop-in
KDA 3.2-100-3-A00-W1	3.2	100	300	Forced	100 A version for mid-size spindles
KDA 3.3-050-3-A00-W1	3.3	50	300	Forced	Low-current 3.3 for light spindles
KDA 2.1-100-3-A00-W1	2.1	100	300	Forced	Older 2.1 hardware, 100 A; same bus
KDA 3.2-150-3-A00-W1	3.2	150	300	Forced	Variant with auxiliary encoder input

Ordering code

KDA 3.2-050-3-A00-W1-220

KDA 2.1-150-3-A00-W1-220

KDA 2.1-100-3-A00-W1

KDA 2.1-050-3-A00-W1

Error code	What it means
F218	Heatsink over-temperature shutdown
F219	Motor over-temperature shutdown (thermistor > 155 °C)
F220	Bleeder-resistor over-temperature
F226	DC-bus undervoltage while drive is enabled
F228	Excessive control deviation (cannot follow command)
F229	Encoder 1 failure – quadrant error
F230	Max. signal frequency of encoder 1 exceeded
F233	External +24 V power-supply error
F234	Emergency-Stop active
F236	Excessive position-feedback difference

Frequently Asked Questions about KDA 3.3-150-3-A00-W1:

Q: Can the unit be used outdoors?

A: The unit can be used outdoors when mounted inside a cabinet.

Q: What is the maximum permitted site elevation with reduced nominal data?

A: The maximum permitted site elevation with reduced nominal data is 5000 meters.

Q: What is the permitted humidity?

A: The permitted humidity is F as per DIN 40 040.

Q: What is the weight of the blower?

A: Weight of the blower is 4.2 kilograms.

Q: What is the weight of the spindle drive?

A: Weight of the spindle drive is 17.4 kilograms.

Internal Product Review

‘‘KDA 3.3-150-3-A00-W1 is a main spindle drive designed for accurate control of compatible motors. It has a DC bus voltage of 300 VDC and a current rating of 150 A making it an ideal fit for heavy duty applications.’’