VT-MSPA2-2X-F5-000-000 Bosch Rexroth Indramat 2.7 Amp IP20 Drive Module
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R901439038
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
The Bosch Rexroth Indramat VT-MSPA2-2X-F5-000-000 is part of the VT-MSPA Drives series and features current command input with support for two control solenoids. This drive operates at 24 VDC with a maximum current consumption of 2 Amps and has an IP20 protection class. It is connected using 12 spring-type terminals and supports a solenoid current up to 2.7 Amps.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The VT-MSPA2-2X-F5-000-000 belongs to the VT-MSPA Drives series produced by Bosch Rexroth Indramat. It is a compact electronic drive that supplies regulated current to two on-board solenoids in hydraulic or pneumatic actuators used throughout industrial automation. By translating a current-mode command signal into a controlled output, the module serves as the intermediary between a motion controller and field devices, allowing proportional positioning or force control while occupying a small footprint inside a cabinet. Because it controls two solenoids on one module, it suits proportional valves and similar actuators that need stable, repeatable electrical drive on each channel.
The drive is intended for systems powered from a nominal 24 VDC bus and will remain functional between 18 VDC and 36 VDC, giving the supply some tolerance when line voltage fluctuates. Under worst-case loading, it draws 2 A, which corresponds to a maximum power demand of 48 W; cabinet power supplies and heat dissipation should be sized for that value. The electronics require a minimum 1000 Ω load on the solenoid circuit, so coil selection must meet that minimum load requirement to avoid overcurrent. Two internal current regulators share the bus, letting both control solenoids receive independent drive while the residual ripple is limited to 2.5 Vpp for smooth actuation.
Command signals are accepted as a current loop, and the 100 Ω current input load allows standard 0–20 mA transmitters to drive the card without undue burden, while the voltage input path shows a 200 kΩ resistance that helps protect upstream analog hardware. The device connects through 12 spring-type terminals, simplifying field wiring, and the terminal arrangement helps keep supply, input, and output wiring organized inside the panel. Protection relies on a 3.15 A time-lag fuse while the initial inrush is capped at 4 A. Steady-state solenoid drive is limited to 2.7 A per channel, and the overall assembly carries an IP20 rating appropriate for installation inside enclosed panels.
Frequently Asked Questions about VT-MSPA2-2X-F5-000-000:
Q: What is the required operating voltage for the VT-MSPA2-2X-F5-000-000 drive?
A: The VT-MSPA2-2X-F5-000-000 operates with a supply voltage of 24 VDC.
Q: What kind of command input does the VT-MSPA2-2X-F5-000-000 support?
A: This unit uses a current command input type for operation.
Q: What is the maximum solenoid current supported by the VT-MSPA2-2X-F5-000-000?
A: The maximum solenoid current this drive can handle is 2.7 A.
Q: How many and what type of terminals are available on the VT-MSPA2-2X-F5-000-000?
A: A total of 12 spring-type terminals are provided for electrical connections.
Q: What type of external fuse should be used with the VT-MSPA2-2X-F5-000-000?
A: The recommended external fuse is a 3.15 A time-lag fuse for safe operation.
