VT-MSPA2-2X-A5-1A0-000 Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R901505407
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
Current response time:
6 Minutes
22 Seconds
The Bosch Rexroth Indramat VT-MSPA2-2X-A5-1A0-000 is part of the VT-MSPA Drives series and operates at 24 V with a maximum solenoid current of 2.7 Amps. It features an IP20 protection class, supports a minimum load impedance of 1000 Ohms, and weighs 0.14 kilograms. The drive uses a 3.15 Amp time-lag external fuse and is rated for altitudes up to 2000 meters.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The VT-MSPA2-2X-A5-1A0-000 is supplied by Bosch Rexroth Indramat as part of the VT-MSPA Drives series. This plug-in module is a drive card intended to regulate proportional solenoids in hydraulic or pneumatic assemblies commonly found in automated machinery. By converting a low-voltage command into a controlled output current, it supports repeatable actuation and stable position holding in closed-loop industrial systems. Its plug-in format also allows the card to be installed in compact control cabinets where space is limited. That makes it suitable for applications where a controller must vary valve current smoothly rather than switch the load on and off.
The card operates from a nominal supply of 24 V, letting it interface directly with standard machine control buses and power supplies. Circuit protection is handled externally with a 3.15 A time-lag fuse that tolerates startup inrush yet disconnects under extended overcurrent conditions. At the output stage, the amplifier can source up to 2.7 A of continuous current to a proportional solenoid so force can be modulated over the full stroke. Control inputs are read through a buffering network that presents 200 kΩ of voltage input resistance, which minimizes loading on PLC analog channels. The driven load must present at least 1000 Ω of impedance to support stable current regulation across the valve coil.
The electronic design keeps supply quality within a residual ripple of 2.5 Vpp, supporting stable magnetic force even when plant power fluctuates. The unit can be installed up to 2000 m above sea level, and the ambient temperature change should not exceed 5 °C per minute during operation. Mechanical protection is rated at IP20, so the board must be mounted inside a cabinet but remains protected against accidental finger contact. The assembly weighs only 0.14 kg, which helps reduce the load on card guides or mounting hardware in modular enclosures. Cabinet installation also helps keep the electronics away from direct contact and common airborne contamination inside the machine area.
Frequently Asked Questions about VT-MSPA2-2X-A5-1A0-000:
Q: What is the required operating voltage for the VT-MSPA2-2X-A5-1A0-000 drive?
A: The VT-MSPA2-2X-A5-1A0-000 operates at a nominal voltage of 24 V.
Q: What is the maximum solenoid current output of the VT-MSPA2-2X-A5-1A0-000?
A: This drive can supply a maximum solenoid current of 2.7 A to connected devices.
Q: What is the maximum installation altitude of the VT-MSPA2-2X-A5-1A0-000?
A: The VT-MSPA2-2X-A5-1A0-000 is rated for installation up to 2000 meters above sea level.
Q: What type and rating of external fuse is required for the VT-MSPA2-2X-A5-1A0-000?
A: A time-lag external fuse rated at 3.15 A is recommended for this model.
Q: What protection class does the VT-MSPA2-2X-A5-1A0-000 drive offer?
A: This unit is rated at protection class IP20 and provides basic ingress protection.
