VT-HNC100-1-2X-W-08-0-D Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R900750908
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
The VT-HNC100-1-2X-W-08-0-D is a digital axis controller manufactured by Bosch Rexroth Indramat and is part of the VT-HNC Digital Axis Controllers series. It is designed for one hydraulic axis, features 8 digital input/output channels, and supports wall mounting installation. The controller provides 4 voltage input channels with a resistance of 200 kiloohms and 2 current output channels, and has a weight of 1.0 kilogram.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The VT-HNC100-1-2X-W-08-0-D is a digital axis controller manufactured by Bosch Rexroth Indramat for the VT-HNC Digital Axis Controllers series. It serves as the closed-loop control unit of a hydraulic positioning system, translating numeric motion commands into metered valve currents so one cylinder or actuator follows programmed trajectories in industrial automation cells. Within the Digital NC control HNC100 product line, it combines motion logic and signal conditioning in a single enclosure.
The configuration covers 1 hydraulic axis, and the software is arranged for stand-alone operation because the unit is supplied without a fieldbus. Command strings and diagnostics move through a RS232 (9.6 KBaud) interface. Four differential voltage inputs provide 5 mV resolution with 200 kΩ ±2% impedance, while two current inputs resolve 5 µA against 100 Ω ±0.2% termination. Two current outputs deliver servo currents, and four voltage outputs can drive external electronics up to ±10 mA. Eight configurable digital lines support interlock or trigger tasks. Electrical demand is 8 W, which helps keep internal heat generation low inside a cabinet. Despite the full set of analog and logic channels, the aluminum housing measures only 71 x 155 x 204 mm and has a mass of 1.0 kg, which simplifies installation in existing panels.
The electronics use both volatile and non-volatile memory to retain machine data appropriately during operation and shutdown. Program code occupies 1 MB of flash, working buffers use 256 KB of RAM, and parameters are stored in an 8 KB EEPROM that retains data during power loss. This memory arrangement separates firmware storage, temporary processing, and retained parameter data into dedicated areas. Calibration for HR1000 and HR2000 inductive position sensors is factory preset, which removes the need for field scaling. As part of Component Series 2, the unit is supplied with flanges for wall installation that keep wiring accessible.
Frequently Asked Questions about VT-HNC100-1-2X-W-08-0-D:
Q: How many hydraulic axes can the VT-HNC100-1-2X-W-08-0-D control?
A: The VT-HNC100-1-2X-W-08-0-D is designed for control of a single hydraulic axis.
Q: Does the VT-HNC100-1-2X-W-08-0-D include a bus connection feature?
A: This axis controller is built without a bus connection, which may limit external communication options.
Q: How many digital input/output channels are available on the VT-HNC100-1-2X-W-08-0-D?
A: It supports 8 digital input or output channels for versatile interfacing with external signals or devices.
Q: What type of inductive position sensor can the VT-HNC100-1-2X-W-08-0-D work with?
A: The controller features a calibrated inductive position sensor compatible with HR1000 and HR2000 models.
Q: What type of installation does the VT-HNC100-1-2X-W-08-0-D require?
A: The VT-HNC100-1-2X-W-08-0-D is intended for wall mounting installation.
