VT-HACD-DPC-1-2X-V0-1-C-0 Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R901119888
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
Current response time:
5 Minutes
39 Seconds
The Bosch Rexroth Indramat VT-HACD-DPC-1-2X-V0-1-C-0 belongs to the VT-HACD Digital Axis Controllers series and features a CANopen bus interface with a Euro-card 100 x 160 mm card format. It operates on 24 VDC, draws 150 mA current, and provides both RS232 serial and DIN 41612 Form G connector standards. The controller has a scan rate of 2 milliseconds, encoder input frequency of 100 kHz, and weighs 0.2 kg.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The VT-HACD-DPC-1-2X-V0-1-C-0 digital axis controller is produced by Bosch Rexroth Indramat and belongs to the VT-HACD Digital Axis Controllers series. Intended for electro-hydraulic motion control, the board generates drive commands, evaluates sensor feedback, and interfaces with plant networks to synchronize a single closed-loop axis. Installed as a rack-mounted card, it supplies reference signals to proportional valves and interprets encoder pulses so that cylinders or motors follow the programmed profile with repeatable accuracy. This arrangement allows hydraulic actuation and feedback processing to be handled within one compact control module.
The module runs on a stabilized 24 VDC logic supply and typically draws 150 mA, which keeps demand on the cabinet rail low. Network traffic is exchanged over CANopen, and a secondary RS-232 port provides direct serial access for setup and diagnostics. Field and sensor wiring terminates on a 64-pin male connector that matches the Euro-card 100 × 160 mm format. The controller samples its analog channels every 2 ms, allowing fast response to pressure or position changes. ±10 V reference outputs drive external amplifiers, and the current input path presents 100 Ω of resistance to transducers so measurement signals are not distorted by excessive loading.
The backplane interface conforms to DIN 41612 Form G, and the voltage input stage offers 100 kΩ of impedance to high-level sensors, which helps preserve signal quality across long cable runs up to the local bus limit of 280 m. Encoder channels accept frequencies up to 100 kHz, supporting precise feedback on fast-moving axes, and each digital output can source 30 mA for opto-isolated relays or indicator lamps. Despite these capabilities, the board weighs only 0.2 kg, which keeps mechanical load low on card guides and supports. Its low mass also helps maintain stable seating in densely populated racks where secure backplane contact is important.
Frequently Asked Questions about VT-HACD-DPC-1-2X-V0-1-C-0:
Q: What type of bus interface is available on the VT-HACD-DPC-1-2X-V0-1-C-0 controller?
A: The VT-HACD-DPC-1-2X-V0-1-C-0 features a CANopen bus interface for communication.
Q: What is the required operating voltage for the VT-HACD-DPC-1-2X-V0-1-C-0?
A: This model operates with a supply voltage of 24 VDC.
Q: What is the maximum encoder input frequency for the VT-HACD-DPC-1-2X-V0-1-C-0?
A: The controller supports an encoder input frequency of up to 100 kHz.
Q: What connector standard is used on the VT-HACD-DPC-1-2X-V0-1-C-0 axis controller?
A: It uses a DIN 41612 Form G connector standard for secure connections.
Q: What is the physical card format of the VT-HACD-DPC-1-2X-V0-1-C-0 controller?
A: This card uses the Euro-card 100 x 160 mm format for installation.
