VT-HACD-1-10/V0/1-D-0 Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R901040277
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
The Bosch Rexroth Indramat VT-HACD-1-10/V0/1-D-0 is part of the VT-HACD Digital Axis Controllers series and offers 6 analog inputs and 3 analog outputs with a 1.25 mV voltage resolution. It operates on a 24 VDC supply voltage, supports 8 digital inputs and 7 digital outputs, and uses a 64-pin DIN 41612 Type G connector.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The VT-HACD-1-10/V0/1-D-0 is a plug-in digital axis controller produced by Bosch Rexroth Indramat for the VT-HACD Digital Axis Controllers series. It governs hydraulic or electromechanical axes by converting set-point data into regulated drive commands and by evaluating sensor feedback to maintain position, velocity, or force. In automated production cells, the card provides cycle-synchronized control so that cylinders, motors, and auxiliary actuators follow machine logic with minimal deviation. Because command generation and feedback evaluation are handled on the same card, the module supports stable axis response during repetitive machine sequences and coordinated motion tasks.
This controller provides 6 analog inputs that accept ±10 V or 0–20 mA transducers, and these channels allow simultaneous monitoring of position, pressure, and auxiliary sensors. Eight digital inputs are available for limit switches or mode selection, and the 8 channels are scanned together with a 2 ms sample time so discrete events are incorporated into every control cycle. A reference output of ±10 V is included for sensor excitation or test purposes. Output capabilities consist of three analog command channels, seven digital drivers, and a single AO1 current stage that can drive loads up to 500 Ω. Protection of the supply rail is handled by a 4 A slow-blow fuse, while the board itself draws only 250 mA when idle. This mix of signal paths allows the controller to process feedback, switch states, and output commands within one compact control stage.
All signals reach the unit through a 64-pin DIN 41612 Type G back-plane connector, simplifying rack installation and orderly signal routing inside multi-card systems. The primary voltage channel delivers an AO1 resolution of 1.25 mV, which supports fine valve modulation without external attenuators. Physical dimensions are confined to a 100 x 160 mm Eurocard format, so multiple axes can be stacked in standard enclosures. The power section tolerates a nominal 24 VDC input, and operation is maintained down to 21 V and remains consistent up to a 35 V ceiling, allowing use on supplies that experience moderate fluctuation. The compact card format also helps preserve cabinet space while keeping control and I/O functions centralized within the rack.
Frequently Asked Questions about VT-HACD-1-10/V0/1-D-0:
Q: How many analog input channels does the VT-HACD-1-10/V0/1-D-0 controller provide?
A: The VT-HACD-1-10/V0/1-D-0 supports 6 analog inputs for signal control.
Q: How many digital outputs are available on the VT-HACD-1-10/V0/1-D-0?
A: This controller features 7 digital output channels for external device control.
Q: What is the required supply voltage for the VT-HACD-1-10/V0/1-D-0 digital axis controller?
A: The supply voltage for the VT-HACD-1-10/V0/1-D-0 is 24 VDC.
Q: What fuse rating is specified for the VT-HACD-1-10/V0/1-D-0 controller?
A: The fuse installed must be rated at 4 A slow-blow for safety and protection.
Q: Which type of connector is used on the VT-HACD-1-10/V0/1-D-0 device?
A: This model utilizes a 64-pin DIN 41612 Type G connector.
