MTS-R02.2-M2-S4-NN-NN-FW Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R911305752
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
Current response time:
4 Minutes
39 Seconds
The Bosch Rexroth Indramat MTS-R02.2-M2-S4-NN-NN-FW is part of the MTS Servo Control Modules series and operates with a nominal supply voltage of 24 VDC and a maximum current consumption of 0.7 Amps. It features multiple communication interfaces (RS232, RS422, and RS485), an SPC operating mode with 2 MB RAM, and a protection category of IP20. The module has 2 required slots, 3 optional slots, and supports up to 4 Bt devices with a maximum Bt bus length of 50 meters.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The MTS-R02.2-M2-S4-NN-NN-FW is a plug-in servo control module produced by Bosch Rexroth Indramat and supplied in the MTS Servo Control Modules series. Installed in a modular drive rack, the board serves as the local sequencing and communication center for multiple drive axes. It hosts the application program, manages data exchange with higher-level PLCs, and sends setpoint commands to attached power sections. Placing motion logic close to the drives helps reduce bus delay and supports coordinated operation in conveyor, packaging, and assembly equipment.
The controller operates from a nominal supply of 24 VDC and can draw up to 0.7 A during peak processing loads. Programming, service access, and field networking use the asynchronous interface set RS232/RS422/RS485, which allows direct connection to external controllers or service computers without additional protocol converters. For intra-rack synchronization, it connects to the proprietary Bt system through a D-SUB 9 Female connector, and copper runs on that link may extend up to 50 m before signal regeneration is needed. This arrangement supports organized cabinet wiring while keeping communication paths straightforward.
The Bt master can supervise up to 4 downstream drive or I/O slaves, which suits smaller machine cells and compact automation sections. Application growth is supported by SPC with 2 MB RAM for program storage and process variables, while 3 optional slots can accept additional serial or fieldbus modules to match the required network layout. The housing has an IP 20 rating, so the module is intended for installation inside a closed electrical enclosure. The board occupies two rack slots, and the modular layout leaves room for expansion cards without changing the base control concept. Supply conductors sized to 1.5 mm² are appropriate for its power connection.
Frequently Asked Questions about MTS-R02.2-M2-S4-NN-NN-FW:
Q: What is the nominal supply voltage required for the MTS-R02.2-M2-S4-NN-NN-FW module?
A: The MTS-R02.2-M2-S4-NN-NN-FW servo control module operates with a nominal supply voltage of 24 VDC.
Q: What is the maximum Bt bus length supported by the MTS-R02.2-M2-S4-NN-NN-FW?
A: This control module supports Bt bus lengths up to a maximum of 50 meters.
Q: Which communication interfaces are available on the MTS-R02.2-M2-S4-NN-NN-FW control module?
A: The MTS-R02.2-M2-S4-NN-NN-FW provides a combination of RS232, RS422, and RS485 interfaces for communication and programming.
Q: How many Bt devices can the MTS-R02.2-M2-S4-NN-NN-FW module support?
A: Up to four Bt devices can be connected to this module simultaneously.
Q: What level of protection does the MTS-R02.2-M2-S4-NN-NN-FW offer?
A: The protection category for this product is IP 20, indicating limited protection against solid objects.
