MS2N07-C1BRL-BMVH1-NNNNN-NN
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R914000912
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
The Bosch Rexroth Indramat MS2N07-C1BRL-BMVH1-NNNNN-NN belongs to the MS2N Synchronous Servo Motors series and features protection class IP65. This motor is equipped with natural convection cooling and an integrated multiturn EnDat 2.2 encoder. It delivers a rated torque of 12 Nm and a maximum torque of 28.7 Nm.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The component MS2N07-C1BRL-BMVH1-NNNNN-NN is a synchronous servo motor which signals a compact frame devoted to precise motion control. The “07” frame size appears on the data sheet that shows mechanical compatibility with standard mounts. With a natural convection mechanism for cooling purposes, it defines the thermal mode which removes the need for external fans in steady operation. The rated speed of 3000 RPM appears in the technical table setting the nominal rotational benchmark for matching drive electronics.
The device with a rated torque value of 12 Nm is listed in the specification which provides continuous torque capacity for steady-state loads. 28.7 Nm maximum torque is recorded which allows short duration load peaks without tripping. Its rated power 3.77 kW is specified for the winding, defining the continuous mechanical power output at nominal speed. This motor’s rated current of 8.4A is given in the electrical data that determines conductor sizing and drive current limits. Protection class IP65 is quoted on the nameplate that protects the internals from dust particles and low-pressure water jets in industrial settings. Integrated multiturn EnDat 2.2 encoder appears as feedback type which enables high-resolution position feedback and persistent absolute position after power cycles.
MS2N07-C1BRL-BMVH1-NNNNN-NN servo drive repeats at the header while winding speed 4,500 min reflects the motor winding design and influences maximum allowable mechanical speed. Its holding brake equipped appears under options to secure the shaft during power-off or emergency stops. Shaft is described as smooth with no shaft seal appearing in the product notes which eases coupling and simplifies shaft machining. Featuring an electrical connection with M40 angle plug turnable appears in the connector data, allowing flexible cable routing during installation. Also, the permanently greased deep groove ball bearings appear in the operating instructions reduce maintenance intervals and support extended bearing life under standard loading conditions.
Frequently Asked Questions about MS2N07-C1BRL-BMVH1-NNNNN-NN:
Q: What frame designation applies to MS2N07-C1BRL-BMVH1-NNNNN-NN and why is it relevant?
A: The frame size 07 applies to this part number which standardizes flange dimensions and shaft interface, and this ensures mechanical interchangeability.
Q: What nominal speed is specified for MS2N07-C1BRL-BMVH1-NNNNN-NN and what does that enable?
A: A rated speed of 3000 rpm is specified for MS2N07-C1BRL-BMVH1-NNNNN-NN which establishes the rotational reference for torque and power calculations.
Q: What continuous torque rating does MS2N07-C1BRL-BMVH1-NNNNN-NN carry and what system behavior follows?
A: The motor lists a rated torque of 12 Nm which defines continuous torque capability under nominal thermal limits. This rating informs gearbox selection and continuous load carrying capacity for motion profiles.
Q: What rated power is provided for MS2N07-C1BRL-BMVH1-NNNNN-NN and how does that guide system design?
A: This rated power of 3.77 kW is declared which describes continuous mechanical output at rated speed and it determines thermal design, spindle sizing and motor selection for sustained workloads.
Q: What rated current is shown for MS2N07-C1BRL-BMVH1-NNNNN-NN and what electrical planning follows?
A: A rated current of 8.4 A is listed which sets the steady-state current draw at rated operation. This feature guides cable sizing, fuse selection, and drive current limit settings in electrical installation.
