MHD093B-058-NP1-BN Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R911319526
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
Current response time:
3 Minutes
16 Seconds
The Bosch Rexroth Indramat MHD093B-058-NP1-BN is a servo motor from the MHD Synchronous Motors series with a continuous standstill torque of 17.5 Nm and a keyed shaft design. It features digital servo feedback for position detection, liquid cooling, and an IP65 degree of protection. This model includes a holding brake with 22.0 Nm braking torque and supports ambient operating temperatures from 0 to 40 °C.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The MHD093B-058-NP1-BN is a servo motor produced by Bosch Rexroth Indramat for the MHD Synchronous Motors series. It converts three-phase drive power into controlled mechanical motion for pick-and-place modules, machining centers, and packaging equipment. Through integrated feedback and matched winding design, the unit supports synchronized positioning tasks that demand consistent torque delivery over extended duty cycles. This design also helps maintain stable response during repeated start-stop cycles and coordinated axis motion.
The motor supplies a continuous standstill torque of 17.5 Nm, so static load can be held without additional gearing while the drive current stays within continuous limits. An enclosure rating of IP65 seals the stator against dust ingress and low-pressure water jets, allowing installation outside a cabinet. Heat is extracted through liquid cooling, meaning coolant channels in the housing carry thermal energy away and keep winding temperatures below the Class F limit. Rotor alignment is referenced to a centering pilot of 130 mm, and the mounting interface follows a square flange footprint of 140/150 mm. Digital servo feedback (HSF) delivers high-resolution rotor position to the drive through an optical measuring method, supporting fast control loops and accurate speed regulation during contouring and indexing.
A holding brake integrated into the rear housing supplies 22.0 Nm of static torque, so vertical axes remain locked when power is removed. Position repeatability is supported by a system accuracy of ± 0.5 angular minutes, which works with the relative position detection scheme to enable fine incremental moves. Ambient ranges from -20 to +80 °C for storage and 0 to 40 °C during operation permit staging and service in ordinary factory climates. The shaft is keyed and protected by a positive shaft seal, while Class F insulation tolerates high winding temperatures under transient overload. Wiring exits on side B through an output connector, and installation is permitted up to 1000 m above mean sea level. This layout also supports straightforward cable routing in compact machine frames.
Frequently Asked Questions about MHD093B-058-NP1-BN:
Q: What type of cooling system does the MHD093B-058-NP1-BN motor use?
A: The MHD093B-058-NP1-BN supports liquid cooling for heat management during operation.
Q: Does the MHD093B-058-NP1-BN come with a holding brake and what is its torque?
A: This motor includes a holding brake with a torque rating of 22.0 Nm.
Q: What is the degree of protection for the MHD093B-058-NP1-BN servo motor?
A: The MHD093B-058-NP1-BN has an IP65 protection rating, meaning it is dust-tight and resistant to water jets.
Q: What kind of encoder and position detection does the MHD093B-058-NP1-BN motor employ?
A: This model features digital servo feedback (HSF) for encoder type with optical measurement and provides relative position detection.
Q: What is the continuous standstill torque of the MHD093B-058-NP1-BN?
A: The continuous torque at standstill for this motor is 17.5 Nm.
