HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R911339936
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
The Bosch Rexroth Indramat HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW is a drive controller from the HCS IndraDrive Controllers series. It supports a SERCOS III master communication interface and is equipped with a MultiEthernet port. The controller features an internal air cooling method using an integrated blower and has a peak device current of 3 Amps.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW belongs to the HCS IndraDrive Controllers series produced by Bosch Rexroth Indramat. It is an AC drive controller that closes the control loop between a PLC and IndraDyn or third-party servo motors. This arrangement allows the controller to regulate motor response while following commands from the higher-level system. The unit handles motion commands, protective functions, and diagnostic tasks in industrial automation cells.
The controller draws power from a three-phase supply rated at 3 x AC 110…230 V ±10%, so it can connect directly to low-voltage factory mains without an external transformer. A device peak current of 3 A is available for short acceleration or positioning pulses before thermal limits intervene. Communication with higher-level motion controllers is handled by the SERCOS III master port, which supports cyclic data exchange and cross communication between multiple drives. For non-SERCOS networks, an integrated MultiEthernet interface supports EtherNet/IP, PROFINET, and EtherCAT, so the same hardware can be used across different control platforms. Motor feedback is received through the IndraDyn Hiperface/EnDat 2.1/2.2 encoder input, and this allows absolute position capture at power-up when a compatible encoder is used. Air cooling is provided by an internal blower, and the housing has an IP20 rating for installation inside a protected cabinet.
The power section is paired with a control section classified as ADVANCED, which provides extended functions such as positioning modules and drive-based logic. The unit is hardware revision 1. Integrated functional safety includes STO and SBC, which disconnect torque and control the brake command within milliseconds when a safety channel is triggered. The drive uses the Infeeding / Feeded supply concept, so it can share a common DC bus with energy recovery to a front-end module.
Frequently Asked Questions about HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW:
Q: What type of communication interface is available on the HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW drive controller?
A: This controller uses a SERCOS III master interface with cross communication capabilities.
Q: How is the HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW cooled during operation?
A: The device operates with an internal cooling method using an integrated blower.
Q: What is the peak current delivered by the HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW controller?
A: This drive controller provides a device peak current of 3 A for connected loads.
Q: What is the supported input mains voltage range for the HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW?
A: The HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW supports a mains voltage input of 3 x AC 110 to 230 V ±10%.
Q: What safety interfaces are included on the HCS01.1E-W0003-A-02-A-CC-EC-ET-L4-NN-FW drive controller?
A: STO (Safe Torque Off) and SBC (Safe Brake Control) are provided as safety interfaces on this model.
