CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R911334233
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
Current response time:
6 Minutes
27 Seconds
The Bosch Rexroth Indramat CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW is part of the CSH Advanced Controllers series and features two analog outputs with a base power draw of 8.5 Watts. It offers a parallel interface for control communication and cross communication via SERCOS III Master. The controller supports 16 digital inputs and 16 digital outputs, with a digital output current of 500 mA and relay contacts rated at 24 V DC, 1 A.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW is a control section produced by Bosch Rexroth Indramat for the CSH Advanced Controllers series. Mounted inside IndraDrive power units, the card serves as the dedicated axis processor that converts PLC motion commands, evaluates encoder signals, and issues gate drive pulses so a servo follows precise speed or position references. By combining signal conditioning and network routing on one module, it supports compact automation cells found in packaging, material handling, and printing equipment. It also centralizes motion logic and feedback handling in the drive, which helps the axis respond consistently during synchronized machine cycles.
Discrete and analog I/O resources are provided directly on the module. The parallel terminal strip offers 16 In / 16 Out lines that react within a maximum pulse width of 100 ms, and two ±10 V analog outputs give scaled velocity or torque references to legacy drives. Each digital output can source up to 500 mA, enough to energize small relays or indicator lamps without auxiliary drivers. During startup, the input bus can momentarily draw 4 A, but once the logic rails are charged the steady base power requirement falls to 8.5 W, which helps limit additional heat inside the control cabinet. An ENS supply of 12 V powers the sine encoder interface operating at 4 kHz, while separate 24 V logic feeds the relay contact pair.
High-speed communication links tie the controller to external devices. Axis-to-axis data is exchanged by a SERCOS III master, and host commands can enter through a parallel interface that complies with the motion control profile. The CCD Ethernet port follows IEEE 802.3 and uses a 100Base-TX connector for network access. Internal PWM drivers are timed by a maximum switching frequency of 16 kHz, and the relay output is rated for 24 V DC, 1 A to switch brakes or contactors. Position feedback is accepted from IndraDyn, HIPERFACE, 1 Vpp primary encoders, and from resolver or HSF secondary transducers. This range of feedback options lets the same control section work with different motor and encoder combinations across mixed machine layouts.
Frequently Asked Questions about CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW:
Q: How many analog outputs are available on the CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW controller?
A: The CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW controller features 2 analog outputs, allowing integration with multiple analog devices.
Q: What is the parallel I/O configuration for this Bosch Rexroth Indramat controller?
A: This controller supports parallel I/O with 16 input and 16 output channels for flexible connectivity.
Q: Which primary encoder interfaces are supported by the CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW?
A: For primary encoder feedback, this model supports IndraDyn, HIPERFACE, and 1 Vpp interfaces.
Q: What type of cross communication interface does this controller offer?
A: The CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW uses SERCOS III Master for cross communication between devices.
Q: Which network standard is used for the CCD connection on the CSH01.3C-PL-ENS-EN1-CCD-NN-S-NN-FW?
A: IEEE 802.3 is the CCD network standard provided with this controller for reliable Ethernet networking.
