CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R911317389
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
Current response time:
3 Minutes
29 Seconds
The Bosch Rexroth Indramat CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW is part of the CSH Advanced Controllers series and features a Standard Control Panel with a single-line display. It supports PROFIBUS master communication via a D-Sub 9-pin female connector and offers digital inputs rated at 24 V, 3 mA, as well as analog outputs rated at 5 V, 1 mA. This controller provides Safety Technology I/O and cross communication drives, along with Ethernet-based engineering and RS232 serial interfaces.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW is a modular control section built by Bosch Rexroth Indramat for the CSH Advanced Controllers series. It slides into an IndraDrive power module and executes motion commands, handles fieldbus traffic, and conditions encoder feedback for one or more servo axes. Within an automated cell, it serves as the logic core that sequences positioning moves, scales process variables, and exchanges status data with higher-level PLC or SCADA hosts. This arrangement lets the control section manage axis-related functions inside the drive platform instead of relying on separate external hardware for each task.
The controller offers an analog monitor channel rated at 5 V, 1 mA, allowing low-burden reference signals to external instrumentation. Eight digital inputs accept machine states at 24 V, 3 mA, while eight transistor outputs switch loads up to 24 V, 0.5 A for lamp stacks or interposing relays. Precise feedback is captured over the X4 port, which supports EnDat 2.1, 1 Vpp, and TTL encoders, matching common Rexroth motors without additional converters. Parameter settings are handled through an Ethernet-based interface, and routine checks can still be run from the standard control panel that uses a single-line display. All user I/O draws from an internal 24 V rail that is limited to 1.1 A to protect the backplane.
Deterministic plant communication is provided by PROFIBUS over the EIA-RS485 physical layer, and cabling terminates at a 9-pin female D-Sub connector to simplify trunk chaining. Cross Communication Drives support is available in the Option-3 slot, allowing peer drives to share setpoints without PLC involvement, while legacy diagnostics remain available through a RS232 service port. Two form-C relay contacts rated at 24 V DC, 1 A supply isolated run and fault signals to external circuits. The X8 encoder interface mirrors the X4 channel so a second position sensor can be connected, and Safety Technology I/O channels are included for category-oriented stop and enable functions.
Frequently Asked Questions about CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW:
Q: What communication protocol does the CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW controller use for master communication?
A: The CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW provides PROFIBUS master communication, enabling integration into automated industrial networks.
Q: What type of control panel and display does the CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW offer?
A: This controller features a standard control panel with a single-line display for basic operational feedback and settings.
Q: What is the digital output capability of the CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW controller?
A: The digital output channels on this model are rated for 24 V at 0.5 A, supporting industrial signal switching.
Q: What type of engineering interface is provided on the CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW?
A: An Ethernet-based engineering interface is included on this model for configuration and diagnostics.
Q: What is the relay contact rating of the CSH01.2C-PB-EN2-EN2-CCD-S1-S-NN-FW controller?
A: The relay contact rating for this controller is 24 V DC at 1 A for interfacing with external devices.
