CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R911315508
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
Current response time:
5 Minutes
40 Seconds
The Bosch Rexroth Indramat CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW is part of the CSH Advanced Controllers series. This controller features two EN2 encoder interfaces with EnDat 2.1, 1 Vpp, and 5 V TTL signal types and supports a supply voltage of 5 V at 350 mA. It provides PROFIBUS control communication with a D-Sub 9-pin female connector, follows the IEEE 802.3 CCD standard, and includes an RJ-45, 8-pin engineering connector supporting 100Base-TX.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW is a plug-in control section manufactured by Bosch Rexroth Indramat for the CSH Advanced Controllers series. Installed inside an IndraDrive modular rack, the board executes motion commands, processes encoder feedback, and manages fieldbus exchanges so multiple servo axes can run in coordinated mode. By combining logic processing with dedicated communication hardware, the card serves as the central command element in packaging, printing, or material-handling machines that demand deterministic positioning and cycle-time repeatability.
Electrical and feedback resources are arranged for direct sensor and encoder support. Each analog channel can source 1 mA or regulate a reference of 5 V, allowing proportional pressure, tension, or speed setpoints to be sent without external amplifiers. Discrete inputs share a rail that can deliver 1.1 A, so light-curtain relays and inductive switches receive sufficient power from the controller itself. Two EN2 connectors accept EnDat 2.1 as well as 1 Vpp or 5 V TTL signals; they provide 5.0 V at up to 350 mA for encoder electronics and expose incremental or absolute data to the drive processor. A master-level cross-communication channel lets neighboring drives exchange position words and diagnostic bits across the backplane with microsecond latency.
All external networking is concentrated on the front panel. Motion command traffic passes over PROFIBUS-DP, implemented according to DIN EN 50 170 and carried by a D-Sub 9-pin female connector that uses EIA-RS485 differential signaling. Service access uses an RJ-45 8-pin socket that supports 100Base-TX Fast Ethernet while complying with the IEEE 802.3 layer, so standard patch cords can connect the controller to a host computer. For legacy tools, a secondary serial port is available, reaching 115 kBaud for trace capture or boot diagnostics.
Frequently Asked Questions about CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW:
Q: How many encoder interfaces are included on the CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW controller?
A: This model features two EN2 encoder interfaces, supporting connections with EnDat 2.1 and 1 Vpp or 5 V TTL encoders.
Q: What type of connector is used for PROFIBUS communication on this controller?
A: The CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW supports PROFIBUS communication through a D-Sub, 9-pin female connector.
Q: What is the analog output voltage specification for the CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW?
A: The analog output voltage on this controller is rated at 5 volts for interfacing with external systems.
Q: Does the CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW support master cross communication?
A: Master cross communication functionality is supported in this controller for coordinated device interactions.
Q: What engineering connector is available on the CSH01.2C-PB-EN2-EN2-CCD-NN-S-NN-FW, and what standard does it support?
A: For engineering purposes, the controller provides an 8-pin RJ-45 connector compatible with 100Base-TX standards.
