4.95 based on 202 reviews

🙶 Wake Ind. did a great job with very fast service getting us a motor driver to repair our critical robot sy... 🙷

VT 2000 S 41 Bosch Rexroth Indramat

No Tariffs On US Orders
  • Rated 4.5 (59 total ratings)
  • Straightforward Pricing: No Rush Fees, No Credit Card Fees
In-Stock, Ships 3-5 Days

Current response time:
6 Minutes 41 Seconds

Preparing your secure checkout page...

The Bosch Rexroth Indramat VT 2000 S 41 is part of the VT 2000 Proportional Amplifiers series and operates on 24 VDC with a maximum solenoid current of 800 mA. This amplifier features a 32-pin male connector, DIN 41612 form D, and has a card size of 100 by 160 mm. The unit weighs 0.1 kg and has a fuse rating of 2.5 A.

Quote Request Form:

Warranty
Wake Industrial Warranty

To contact sales for pricing and lead time:

Payment Methods

Visa
Mastercard
AmEx
Wire Transfer

Shipping Methods

DHL
UPS
FedEx
Freight

Our Credentials

Cary Chamber
DUNS Registered
SAM Registered
BBB Accredited

Product Description:

The VT 2000 S 41 is a proportional amplifier card produced by Bosch Rexroth Indramat for the VT 2000 Proportional Amplifiers series. Mounted in a valve control rack, the board converts low-level command voltages into controlled solenoid current so hydraulic actuators can be driven with repeatable force and position. This arrangement lets a PLC send a simple analog reference while the card handles the current regulation required by proportional valves. Because the output current is regulated rather than applied directly from the command source, the valve receives a stable actuation signal even when coil temperature or supply conditions vary. That behavior supports consistent response in positioning, clamping, and pressure-control circuits.

Normal operation uses a regulated bus of 24 VDC, but the circuitry tolerates supply variation from 22 V to 35 V without losing accuracy. Internal demand stays below <1 A, keeping power draw modest and total dissipation under 25 VA. The input channel interprets the voltage reference on a linear scale of +6 V = 100 %, which provides a direct relationship between command level and valve demand. Loop behavior can be checked at a test pin that reads 1 mV = 1 mA. The closed-loop driver can deliver up to 800 mA to a connected solenoid with 19.5 Ω resistance, allowing full valve stroke while maintaining responsive control.

The card uses a Eurocard footprint of 100 x 160 mm and plugs into a backplane through a 32-pin male, DIN 41612 form D connector. Overall weight is only 0.1 kg, which keeps the module easy to handle during installation, and the front-panel height of 128.4 mm leaves clear access to potentiometers and LEDs. Local electronics share an internal ±9 V reference rail for sensors, and the power path is protected by a 2.5 A T fuse that absorbs slow overcurrent events while allowing brief inrush when the rack is energized. The compact format suits densely populated hydraulic control panels where multiple control cards must be installed side by side without blocking access to adjacent modules.

Actual Current Scale
1 mV = 1 mA
Card Size
100 x 160 mm
Command Value Scale
+6 V = 100 %
Connector Type
32-pin male, DIN 41612 form D
Current Consumption
<1 A
Front Panel Height
128.4 mm
Fuse Rating
2.5 A T
Lower Voltage Limit
22 V
Max Solenoid Current
800 mA
Operating Voltage
24 VDC
Power Consumption
<25 VA
Regulated Voltage
±9 V
Solenoid Resistance
19.5 Ω
Upper Voltage Limit
35 V
Weight
0.1 kg
  • VT 2OOO S 41
  • VT-2000 S 41
  • VT-2000-S-41
  • VT2000-S-41
  • VT2000S41

Frequently Asked Questions about VT 2000 S 41:

Q: What is the operating voltage range of the VT 2000 S 41 amplifier?

A: The VT 2000 S 41 amplifier operates at 24 VDC and can accept voltages between 22 V and 35 V.

Q: What type of connector is used on the VT 2000 S 41 amplifier?

A: The VT 2000 S 41 features a 32-pin male connector designed to DIN 41612 form D specifications.

Q: What is the maximum solenoid current output on the VT 2000 S 41?

A: The maximum solenoid current supported by this amplifier is 800 mA.

Q: What is the power consumption rating for the VT 2000 S 41?

A: This amplifier consumes less than 25 VA of power during operation.

Q: What fuse rating is specified for the VT 2000 S 41 amplifier?

A: The VT 2000 S 41 amplifier uses a 2.5 A T fuse for protection.


Internal Product Review

  • ‘‘The VT 2000 S 41 is a Bosch Rexroth Indramat proportional amplifier designed for stable valve control on a 24 VDC supply. A maximum solenoid current of 800 mA and an actual current scale of 1 mV = 1 mA support precise setup and consistent response during tuning. Low power demand under 25 VA makes the amplifier an efficient and dependable choice for proportional control applications.’’

Motion Industries logo
3M logo
IBM logo
Gexpro Logo
Caterpillar logo
NASA logo
Ford logo
Vallen logo