MKE098B-047-DP1-BENN Bosch Rexroth Indramat
Wake Industrial LLC is not an authorized distributor of this product.
MPN: R911344717
No Tariffs On US Orders- Straightforward Pricing: No Rush Fees, No Credit Card Fees
The Bosch Rexroth Indramat MKE098B-047-DP1-BENN is a servo motor for potentially explosive areas, and is part of the MKE Synchronous Motors series. It features a continuous torque at standstill of 12 Nm, a maximum torque of 43.5 Nm, and includes a holding brake with 11 Nm brake torque. The motor weighs 18 kilograms without the brake and is equipped with an optical encoder (multiturn absolute EnDat2.1) with 2,048 increments.
To contact sales for pricing and lead time:
Payment Methods
Shipping Methods
Our Credentials
Product Description:
The MKE098B-047-DP1-BENN is a servo motor engineered by Bosch Rexroth Indramat for the MKE Synchronous Motors series. Designed for use in potentially explosive areas, it supplies controlled rotary motion to actuators, conveyors, and positioning tables installed in hazardous industrial zones where flammable gases may be present. The motor combines an explosion-protected housing with coordinated feedback so drive controllers can maintain precise speed and torque loops in these automation environments.
The motor uses winding code 047 with a resistance of 8.400 Ω at 20 °C and an inductance of 1.20 mH. It supports a continuous phase current of 9.8 A when the frame temperature rise does not exceed 60 K, and under the same thermal condition it delivers 12.0 Nm of standstill torque. For acceleration peaks, the drive may apply up to 44.3 A RMS, raising shaft output to 43.5 Nm and allowing speeds up to 4500 rpm. The induced voltage at rated speed is 91.0 V per 1000 rpm, and operation is permitted from 0 °C to +40 °C ambient with Class F insulation rated for 155 °C winding temperatures. Electrical terminations are routed on the B-side through a sealed terminal box, which simplifies conduit entry while maintaining the motor's discharge capacity of 6.7 nF for EMC control.
Closed-loop control is handled by a multiturn optical EnDat 2.1 encoder, model M2, that offers 2,048 increments per revolution. Its data are referenced to a torque constant of 1.41 Nm/A for current vector calculations. Dynamic response benefits from a rotor inertia of 0.00430 kg m², and airborne noise is limited to 61.8 dB[A]. A factory-mounted holding brake rated at 11 Nm secures vertical loads when power is removed. The housing meets ATEX requirements and weighs 18.0 kg without the brake. A shaft with a DIN 6885 keyway and a positive shaft seal transmits torque while helping block oil or dust ingress.
Frequently Asked Questions about MKE098B-047-DP1-BENN:
Q: What is the maximum speed supported by the MKE098B-047-DP1-BENN motor?
A: The MKE098B-047-DP1-BENN has a maximum velocity of 4500 min⁻¹.
Q: What type of encoder is used in the MKE098B-047-DP1-BENN motor?
A: This model features an optical multiturn absolute EnDat2.1 encoder for position feedback.
Q: What is the shaft configuration on the MKE098B-047-DP1-BENN motor?
A: The shaft on this motor uses a DIN 6885 keyway and includes a shaft seal for added protection.
Q: Does the MKE098B-047-DP1-BENN motor come with a holding brake?
A: The MKE098B-047-DP1-BENN is equipped with a holding brake that provides 11 Nm of holding torque.
Q: Does the MKE098B-047-DP1-BENN motor comply with any explosion protection standards?
A: This motor meets ATEX housing standard compliance and is suitable for use in potentially explosive environments.
